November 4, 2010

Glass Light Block Tutorial

Want to make one of these cute glass light blocks?

These make great Christmas presents and sell really well. In November and December of 2006 I made and sold over 150 of these. I even made personalized ones as night lights with names like the Sylvana and Wyatt ones above and blocks in memory of loved ones with photos and poems, etc. I still get calls from time to time from people wanting them. I have an order for two for Christmas right now.

What you need:
Photobucket
*Glass block from Lowe's, Home Depot, etc.
*Drill
*1-inch diamond drill bit (these are made for glass)
*Graphic for printing (I use PCCrafter for the graphics on all the above blocks)
*Full sheet sticker label
*Laminator and laminating sleeve
*Ribbon
*6-foot light cord and bulb
*Scissors
*Hot glue gun (oops, forgot to put the hot glue gun and scissors in the pic)

You will need to print your graphics for each side of your block on a full sheet sticker label for the 8 x 8 block like I am using in this tutorial. Cut out your graphic with scissors. You can get more than one on a sheet for the 6 x8 and 4 x 8 blocks. I use the highest quality for printing for mine.
Here are the exact measurements for printing your graphics to fit each size block:

8 x 8 block - 6.74 x 6.74 inches.

6 x 8 rectangular blocks - 4.79 x 6.74 inches.
4 x 8 rectangular blocks - 6.74 x 2.8 inches

Turn your block up on its side and mark the middle like in the pic below.
Put a little water on your block where you are going to drill.
Drill the hole in the bottom of your block with a 1-inch diamond bit for glass. I ordered mine off eBay. I am using a regular drill today but when I was making lots of these I borrowed my brother-in-laws drill press.

Photobucket
I do this either outside or in the sink so I can wash away the glass dust. Keep adding just a little water around your bit as you drill. If the block gets too hot it will crack.

Once the hole is drilled, dump the glass out from the inside of your block and wash your block with water inside and out. Shake as much water out of the block as you can and set it to the side to dry. I stuff a paper towel in the hole to help soak up what water is left inside. While the block is drying, laminate your graphics.

I used the same graphic for both sides on this block but you can use different graphics, a photo, a poem or even family names on one side and a graphic on the other. It's up to you!

Before peeling the paper off the back of your graphics, place them back to back with sticky paper still on and slip them inside the laminating sleeve. This saves you a laminating sleeve by using one for both graphics. Run this through your laminator, flip it over and run it through again. When you trim around the very edges of your graphic and take them apart, you will have two graphics with the fronts laminated and the backs ready to peel.

Photobucket
Run each of these through the laminator one or two more times just to make sure the laminate is on your graphic really well.

Grab your block and lay it flat. Take one graphic and peel the backing off. Holding it almost at the top on each side place your top two corners onto the block.

Photobucket
You want your graphic to fit inside the sunken area and have a little "frame" around the edge. Press the graphic down along the top and then rub it down flat, top to bottom. Once stuck these are not going to come off easily or without tearing your graphic up so make sure you get it where you want it.

Flip your block over and put the graphic on the other side.

You can leave your block like this but I like my blocks with ribbons. These are easy to put on.

Photobucket
Turn your block upside down and put hot glue in a line across the block beside the hole. Fold the edge of your ribbon over and start it here.
Once stuck, flip the block over so the top is up...

Photobucket
Start gluing your ribbon on, make a "bunny ear" and glue it down again.

Photobucket
You want 5 "bunny ears" centered at the top of the block.

Photobucket
Flip the block over and take the ribbon to the bottom and glue it next to the hole.

Photobucket
Flip the block over and put your fingers inside the first two ears and twist in opposite directions. This opens up the ribbon and shapes it.

Photobucket
Do each ear this way until you have your ribbon looking the way you want it.

Photobucket
You can use a little hot glue to keep it in the right place so it looks good on both sides.

Photobucket
I use this light cord and bulb.

Photobucket
I like it better than the string of Christmas lights because you can turn it on and off without unplugging it and you can change the bulb if it burns out.

Photobucket
Insert the bulb and turn it so the cord goes to the side. This allows the block to sit flat. At one time I used the little glass globs as legs for my blocks but they are a pain to keep glued on.
There you have it...
Photobucket
A glass light block to give your home a cozy, warm glow through the Holidays or all year long.


Any questions? Just ask!

Tip from reader Jules: DO NOT USE Lexan or plastic blocks, when these get heated the smoke is toxic.

18 comments:

Millie said...

Very cool! I just love that, but I'm afraid it would be way out of my league. I tend not to do power tools very well. I'll have to show my mom--she could do this.

floweringmama said...

Oh yes, we sold these when I worked at a non-profit organization. Prices ranged from $15 to $35 but we did have to pay a glass company to cut the holes for us. I think it was a dollar a block.

Julie Harward said...

That is amazing and very pretty! ;D

Dawn said...

What a wonderful idea!!!! I would love to try this...my sister and I were going to put on a "girl-craft" weekend...THIS might be just what we are looking for:)
Thanks!!!

Anonymous said...

Those look amazing! Plus you made it look easy enough to do, so I may even have to try it. What great gifts they'd make!

Jen said...

Love Them... really love the chicken one! Very cute Christmas gifts.

TexWisGirl said...

That's really neat! I bet they make wonderful night lights and perfect for putting in the windows as a seasonal decoration. :)

Unknown said...

Love the blocks! Where can I find the cord & bulb? Thanks for your help!
Betsy

Jules said...

I love these, my Dad has been making them for a couple of years. :)

Please make sure your readers DO NOT USE Lexan or plastic blocks. When these get heated their smoke is toxic. A point I had to point out to my father. ;)
Jules @ Trying To Get Over The Rainbow

Kentucky Farm Girl said...

Thanks for the tip Jules. I added it at the bottom of the post. I have never used anything but the glass blocks from Lowes and Home Depot. They do have the predrilled craft blocks at Hobby Lobby but the hole is too big for the light clip on the cord.

Hannah, if you're just looking for a few of the cords they sell them at Wal-Mart this time of year with the Christmas village sets. I bought mine from an online supplier in bulk and saved money when I was making so many of these. I am looking for the name of the company I used but so far can't find the specific one but there are several companies online that sell them and several for sale on eBay. Hope that helps.

tsmith said...

I saw these for the first time at a craft show this year and thought it was a cute idea. Only, the ones I saw were either painted or wrapped with ribbon like a present. I like the way yours look much better with the sticker! I might have to try these now (my husband will love you for giving me a new craft idea ;-) ) Thank you for the tutorial.

Deb said...

Wow! Super cool!! I may have to make one for each of my daughter's rooms. Thank you so much for the great idea!!!

Cheryl said...

Love the blocks. I saw them some where that already had the holes, to drop lights in. Thought it was Lowes, may be wrong.

Janet, said...

Very pretty! I don't have a laminating machine, could you decoupage a graphic on the front and back?

Elly W said...

Nice info here. Keep us these great posts!

Averil said...

I loved your site so much, it's fantastic, I sent it on to my sister in England, she's having a go herself. You've inspired us. Just one question about the Full sheet sticker labels, do you use matte or gloss? Thanks for having such a wonderful site.

Audria said...

Saw this today and love love it !!
PCCrafter says it closed down it's website ..do you have anyother places or any suggestion on what to put on the blocks?

smr61754 said...

I know this is an old post...I just found your blog from a link on Pinterest. Now that they sell the blocks with the holes cut out, its SO easy to make these! I don't have a laminating machine but I use stickers, rub ons and I mod podge things like fancy napkins to the glass. Your chicken caught my eye because I know someone that collects chickens and would probably like one like that. Thanks!

ANNOUNCEMENTS

For those of you who are new followers/readers, don't forget to check out the forum and join in on our discussions there.

My Country Blog of This and That Forum

I love each and every comment my blogging friends leave for me!


All images and graphics on this page were made by me with the exception of that little rooster! He came from Beth Logan's Checkered Chickens at pccrafter.com. Photos were taken by me and graphics were created using Photoshop CS2.
If you see something you like please ask for permission before using it!
Thank you!